This post includes affiliate links, which means that if you make a purchase after clicking on my links, I will receive a commission for the sale.
How many different methods are there to remove the adhesive from automotive window tint? Where do I need to exercise extreme caution? You’ll discover every solution right here!
In most cases, dissolving tint adhesive requires the use of ammonia or detergent. Therefore, these are typical components that we utilized in the process of removing the adhesive from the automobile window tint. But is it possible to complete the task without the use of any chemicals?
We would like to suggest a ready-to-go technique that only requires the acquisition of accessories that are already present in your home, specifically a hair dryer. It’s safe to assume that not all of us keep ammonia in our homes around the clock, right?
We guarantee that even individuals with no prior experience can succeed using this method.
In order to keep the focus of this piece more on a proposal, we will also be revising the ammonia technique in the following with some pointers. Whatever it is that you plan to do with the window adhesive in your vehicle, it will be helpful!
Removing automotive window tint adhesive can be done by everyone!
Remove Window Tint Adhesive from Your Car by Hairdryer
When it comes to dealing with the tint adhesive, all you really need is a hairdryer. You won’t need any other accoutrements. On the other hand, we strongly suggest that you acquire a small straight shaver in addition to a clean cloth. After that, they will make everything much more easily approachable and keep it clean.
Step 1: Get to know the tint edge.
You can see the adhesive edge of the window if you scroll down the window of your vehicle. This edge is also most prominent at the top of the window’s upper edge.
Keep it there for the time being because we need to start the peeling process from this position.
Step 2: Heat the adhesive
We recommend that you maintain the hair dryer set to its highest heat setting. In addition, it would be to your advantage to begin with the exterior and then move on to the interior.
We recommend that you tie the trigger of the hairdryer up so that it won’t move while your fingers have a chance to relax. This is because we are aware that holding the hairdryer trigger for more than two minutes will cause pain on the finger.
The corner is the first location to reach the desired temperature.
The hair dryer will blow quite hot air straight onto the glass door, which is susceptible to cracking when subjected to temperatures that are too high. As a result, it is essential that you maintain the correct distance between the nozzle and the container, which is typically between 1 and 2 inches.
You are going to need a lot of patience for this stage because you are going to have to wait approximately or even more minutes for the tint to melt.
Step 3: Peel-off
When the tint reaches the point where it is soft enough, the adhesive binding power will begin to decrease. At this stage, you will separate the adhesive in the corner so that it is no longer in contact with the glass window.
It is at this point that the blade can be of assistance. Place the blade beneath the adhesive layer, and then separate it from the surface. In the event that the tint melts to an adequate degree, you will be able to obtain the corner very successfully and precisely.
However, using razors requires a cautious touch or you risk scratching your window, even if it is just a hindrance corner. If you scratch your window, it will be an eyesore.
Step 4: Continue peeling off
Continue to work your way out from the corner as you move the hairdryer progressively downward around the room.If you do not want the adhesive to be ruined, you will need to move through this process slowly and carefully. In addition to that, make sure that you heat up the entire area before you begin removing.
If you are unsuccessful in one of the quadrants, you can make up for it by beginning again in the other one.
Step 5: Clean-off
We trust that you have mastered the peeling process by this point.
It’s possible that a hair drier doesn’t generate enough heat to completely melt the tint. As a result, you will need to use soap to remove any trace of the remaining color. After it has had some time to absorb, you can then wipe it away.
Step 6: Cope with the rear door
Because the back windshield has a line to prevent frost buildup, we need to exercise even greater caution. In addition, steaming for at least 7 minutes is required for this region.
You are required to find the freezing line and maintain constant vigilance over it.
Remove Window Tint Adhesive from Your Car by Ammonia or Soap
Step 1: Get everything inside covered
You will apply a significant quantity of liquid to your windshield, and this liquid can wear away leather and fabric. Consequently, the first thing that needs to be done is to place everything inside of plastic containers.
Step 2: Get garbage bag in the size of the window (can measure and cut by razor)
To conceal the view out the window, you will require large-sized, dark garbage sacks to place over it. We recommend placing them on the window and then cutting along the border with a razor for the most accurate measurement possible.
Step 3: Spray liquid
Check that you have a sufficient number of sections of trash bag made of black plastic to cover the window.You can now squirt either ammonia or liquid soap. (you definitely dilute the liquid with water before use). Cover the window with the trash, which, due to the presence of fluid, should adhere to the glass.
Step 4: Peel off
It is expected that the adhesive will disintegrate after it has been soaked for one hour. Now, cut the corner with the blade, and remove the tape after you’ve done so. Due to the irregular ammonia spectrum, the tint may at times still be difficult to release adhesive from. You might be able to cut the portion away with razors, but be careful not to rip the adhesive apart in the process.
Step 5: Clean up
There is a vanishingly small possibility that the liquid will completely remove the tint. If you’re fortunate, all you need is some water to clean everything up, and you’re done!
However, we normally presume that you need to clean up any leftover tint.
To get rid of them, you can re-soak them in ammonia or detergent for an additional hour. This should do the trick. The use of steel wool is another technique that saves time, but you need to be careful that it doesn’t scratch the surface.
When working with chemicals such as ammonia and detergent, it is imperative that you always remember to keep your nose and mouth covered. Failing to do so may result in skin allergies and the inhalation of an unpleasant odor. Anomia has an odor that is not particularly pleasant.
On a bright and hot day, the second technique will be the most efficient and effective, while also requiring the least amount of time. Because of the elevated temperature, the dissolution process will go much more quickly.
And finally, the last thing to consider for either of these recommendations is how to deal with the back door. Because the damage to the blade is invisible to the naked eye, it is best to avoid touching it at all costs while it is in the defrost line.
Although the service to remove automobile window tint adhesive does not cost a lot of money (unless you ask for a luxurious one), you will still have to pay for it whenever your window becomes scratched, unclear, or excessively dark.
Why don’t you just create it yourself using the equipment you have lying around the house?